Learning to Paint: Applying clear coat

February 10, 2021 / SV Gimme Shelter / Leave a comment

I spent an entire morning sanding down the color coat I had applied the day before to remove all of the cardboard and plastic that had stuck to the paint when I flipped various pieces before they had cured. I had previously sanded it all with 400 grit, but this time I wet sanded with 600 grit to get a better finish.

I dug out some wire hangers and worked out a new tactic for the my second attempt at color.

I mixed, re-mixed, and then mixed the color again hoping it would be more red this time around. It looked the same as it had before.

Once I had two nice coats of color back onto the parts, I let them cure for an hour, and I prepped for clear coat.

The Eastwood Clear mixes 2:1, so it’s a bit thicker than the color and base coats that mix 4:1. In the future I think I would add reducer when using it with the turbine sprayer.

The Eastwood instructions only call for two coats of clear, but the Kindig It Paint with the Pros instructions call for five coats of clear. It was going on really thick and really clouding up the air in the garage, so I quit at three coats. There really had been virtually no overspray with the base and color coats, but even using the low VOC activator in the clear coat, it was creating serious fumes. People walking their dogs along the street were coughing as they passed the house.

The first coat went on really well and made the color shine, but the second and third coats went on cloudy and had me worried. Thankfully, they dried clear.

I gave all of the parts plenty of time to cure before touching or moving them this time. I’m proud to say that after having to prime twice and shoot color twice, I got the clear right the first time.

I would have liked less texture in the final project. I think reducer would have helped. As I analyzed the parts in the light, I thought, it’s not TERRIBLE, but I wouldn’t have paid for this job. However, it can only get better after the cut and polish.

Learning to Paint: Laying down color

February 7, 2021 / SV Gimme Shelter / Leave a comment

Before jumping to the color base coat, I decided I need to spend more time working with the gun and attempt the primer again. I diluted it 3:1 instead of 4:1 and made sure I had the paint feed all the way open. I got slightly better coverage, but unfortunately there was still too much texture to the spray.

At left is my second attempt at primer, which still has noticeable texture. At right is a valve cover sanded with 400 grit.

Frustrated, I turned to the internet. After watching a half-dozen videos, it became apparent that to get good results with the turbine sprayer, you HAVE to use the pressure cup. I was using a PPS 2.0 disposable cup liner system. There is actually a 3M PPS pressure cup that uses the disposable liners, but I only had the gravity feed cup. I decided to use the stainless pressure cup that came with the gun for the color round. It made a HUGE difference.

I mixed up the Bonneville Black Cherry. I was really excited about this color, and I have debated whether or not I should paint the entire car with it.

The paint looked very black, but as I stirred, the metallic red began to appear. However, as I sprayed it on, it looked black with a hint of plum. I did some parts with what I would deem a regular coating and some I went heavier to see if it would affect the color at all. However, as it dried it seemed to become more of a bronze champagne? I’m not sure how to describe it. The photos below required the camera exposure to be pumped up to see the color because without direct sunlight, it looks more or less black.

I learned some important lessons this round beyond just the fact that I have to use the pressure cups.

Lesson 1: Laying the paint on thicker did not improve the color, it just caused solvent popping.

Lesson 2: I’ve got to stop painting on a table. The first round of paint keeps drying on the plastic sheet, then it cracks off and blows dust up onto the things I’m painting.

Lesson 3: If I have to flip something I’m painting, give it extra EXTRA time to cure before flipping or it just screws up the paint I’ve already sprayed.

Lesson 4: Don’t remove the coveralls until after you clean the gun or you will probably splash thinned paint droplets all over your clothes.

The valve covers, which were stacked higher than everything else and don’t require flipping were the only pieces that came out “good.” There’s one very small run on one of them, but I can’t decide if it’s worth fixing or not. The oil pan was great until I went over it with a SUPER thick experimental coat to see if I could get more of the red color to come out. The red did show while I was spraying it. It then dried the same color as everything else but with lots of bubbles from solvent popping. I think I’ll re-sand and re-spray it. The air cleaner lid and base both fell victim to having cardboard stick to the bottom side while I painted the top. The snorkel was sitting right on the plastic, and it has plastic coating the entire bottom side now.

I will definitely find a way to hang my parts to do another color coat before I move on to clear coat.

One thing I have decided, I do not want my entire car painted Bonneville Black Cherry. I will not order the paint for my car online. I need to find a local shop where I can lay my eyes on the real colors before I commit to spraying the car with it.

Learning to Paint: The first attempt

February 5, 2021February 5, 2021 / SV Gimme Shelter / Leave a comment

In September 2019, back when the world was normal, and we jumped on airplanes to breath up each other’s exhales without thinking twice, Mary and I made a trip to Salt Lake City.

During that trip Bryce Green and Freddy Carlson taught us how to paint.

When you have pro equipment being set up for you in a climate controlled spray booth with two of the best painters in the world coaching you, it’s hard NOT to paint well. Recreating that magic in my garage has proven to be more of a challenge. I didn’t really have the space or want the noise of an 80 gallon compressor. Additionally, I was going to have to install multiple moisture traps along the walls. I decided to take a chance on an Apollo 5-stage turbine sprayer.

Allegedly it delivers a continuous 9.5 psi of dry air, and it has a nice HVLP gravity fed gun similar to the SATA guns we used during our class. It’s fairly quiet, and I can spray anywhere there’s a wall plug. I’m hoping we can spray varnish and maybe even gel coat on the sailboat as well.

When we learned the Kindig It paint method, it started with bare metal, then epoxy primer, then filler, then polyester primer, then 2k urethane primer, then sealer, then basecoat, and finally clearcoat.

First off, I’m on a budget. Second, I don’t really have the time or energy to take the Cougar all the way down to bare metal. For my test run, I decided to see what would happen if I sanded the parts, used a little rust encapsulator where necessary, then jumped straight to a 2k primer.

By the way, I never thought I’d have a favorite sandpaper, but I ordered several rolls of Indasa paper from Big Kid Blocks, and I have to say, I love Indasa sandpaper. It is so much better than whatever I usually grab at the hardware store. I also highly recommend their Show Gun cleaner and AngelWax products.

All of the engine parts for this test were giveaways from various members of the Southeast Texas Cats Mercury Cougar Club. The valve covers were from a 68 Cougar. The oil pan was from a 65 Mustang. All of the pieces had different color paint and varying amounts of rust. I cleaned them with a wire wheel, but the gold paint on the oil pan was especially stubborn. I gave it all a spray with rust encapsulator, then sanded with 220.

I emptied all 22 ounces of 2k primer onto the parts. At times I felt like I had the gun spraying well, but at times it felt like I was barely getting any paint out at all. I was using a 1.5mm nozzle, but I think I probably needed a 1.8mm. (Unfortunately, I haven’t purchased a 1.8mm.) I kept turning the air pressure up, but in fact, I probably needed to turn it down to increase paint flow.

When the primer dried, it had a very rough texture. It smoothed out easily with 400 grit, but sanding won’t be an option when I get to the color coat.

I finished sanding, wiped it down with paint prep, then re-assessed. The coverage had become a little thin in some places, and there were a few spots showing bare metal.

I decided that instead of moving on to the base coat, it would be better to troubleshoot my issues and try another coat of primer. I’m going to spend more time adjusting the gun and increase the amount of reducer for better flow. Hopefully I’ll have time for attempt number two before the weekend is over.

The Dredge Report

March 5, 2015 / SV Gimme Shelter / Leave a comment

We’ve seen the dredge barge in action a lot lately. It feels good to know that all the money we’re spending on slip fees is actually being put to good use. Watergate has also removed pier 2, and it will soon be replaced with a new floating pier.

Thanks to the many trips of these dump trucks back and forth to the barge, we can actually go sailing in the middle of winter at low tide. At our old marina we would be sitting in the mud from Thanksgiving until St. Patrick’s Day!